deckard1 Posted January 11, 2018 Share Posted January 11, 2018 Hello, Any guesses as to why I am getting audible latency when recording my electric guitar at a buffer setting of 64 samples in Logic? Logic is giving a reading of 5.8 ms for roundtrip latency which, if I am not mistaken, should not be discernible to the human ear. I do not have any plugins on any channel strips either which could be the cause. I tested the exact same setup I have in Logic in another DAW and there was no audible latency whatsoever at a buffer setting of 64. I contacted Apogee tech support thinking it might be the Duet causing the latency. They had me use direct monitoring with the Duet and the audible latency went away, so the Duet checks out fine. Any ideas or suggestions? I am completely stumped so far. Thanks. Quote Link to comment Share on other sites More sharing options...
Eric Cardenas Posted January 11, 2018 Share Posted January 11, 2018 Plug-in latency? Try enabling Low Latency mode when recording. Quote Link to comment Share on other sites More sharing options...
deckard1 Posted January 11, 2018 Author Share Posted January 11, 2018 No plugins being used. I’ll try low latency mode and see what happens. Thanks. Quote Link to comment Share on other sites More sharing options...
triplets Posted January 11, 2018 Share Posted January 11, 2018 Uncheck Core Audio, apply changes. Recheck Core Audio, apply changes. Sometimes that does the trick for latency that shows up out of nowhere. Quote Link to comment Share on other sites More sharing options...
deckard1 Posted January 12, 2018 Author Share Posted January 12, 2018 Uncheck Core Audio, apply changes.Recheck Core Audio, apply changes. Sometimes that does the trick for latency that shows up out of nowhere. That did the trick!!! Thanks!!!! Why did that work exactly? Thanks again. Quote Link to comment Share on other sites More sharing options...
triplets Posted January 12, 2018 Share Posted January 12, 2018 Why did that work exactly? Core Audio and USB go bonkers sometimes. That resets it. Quote Link to comment Share on other sites More sharing options...
deckard1 Posted January 12, 2018 Author Share Posted January 12, 2018 Thanks! Quote Link to comment Share on other sites More sharing options...
deckard1 Posted January 14, 2018 Author Share Posted January 14, 2018 Latency is back. Oy veh. Is there anyway to revert back to 10.3.2? I never had any audible latency problems on 10.3.2. Thanks. Quote Link to comment Share on other sites More sharing options...
triplets Posted January 14, 2018 Share Posted January 14, 2018 Is there anyway to revert back to 10.3.2? I never had any audible latency problems on 10.3.2. Do you have a Time Machine backup? Otherwise, not. Quote Link to comment Share on other sites More sharing options...
deckard1 Posted January 14, 2018 Author Share Posted January 14, 2018 Is there anyway to revert back to 10.3.2? I never had any audible latency problems on 10.3.2. Do you have a Time Machine backup? Otherwise, not. Thanks! I think I do. Will check. Thanks. Quote Link to comment Share on other sites More sharing options...
triplets Posted January 14, 2018 Share Posted January 14, 2018 For future situations, always make a copy of the current Logic app and put it in another folder. That way when you update, you can always revert no problem. Quote Link to comment Share on other sites More sharing options...
deckard1 Posted January 14, 2018 Author Share Posted January 14, 2018 (edited) For future situations, always make a copy of the current Logic app and put it in another folder.That way when you update, you can always revert no problem. Excellent advice. Thank you. I happened to find 10.3.2 on a previous Time Machine backup by chance. How do I replace 10.3.3 with 10.3.2 without replacing everything from the Time Machine backup that has 10.2.2 on it? I just drag 10.3.3 to the Trash and put 10.3.2 in my applications folder? Is that it? It can't be that easy. Thanks. Edited January 14, 2018 by deckard1 Quote Link to comment Share on other sites More sharing options...
triplets Posted January 14, 2018 Share Posted January 14, 2018 How do I replace 10.3.3 with 10.3.2 without replacing everything from the Time Machine backup that has 10.2.2 on it? Select the app, and click Restore. Quote Link to comment Share on other sites More sharing options...
deckard1 Posted January 14, 2018 Author Share Posted January 14, 2018 How do I replace 10.3.3 with 10.3.2 without replacing everything from the Time Machine backup that has 10.2.2 on it? Select the app, and click Restore. Just read your post and did it. That has to be the coolest thing in the world. Quote Link to comment Share on other sites More sharing options...
triplets Posted January 14, 2018 Share Posted January 14, 2018 Just read your post and did it. That has to be the coolest thing in the world. I know, and so many people don't even use Time Machine. Quote Link to comment Share on other sites More sharing options...
deckard1 Posted January 16, 2018 Author Share Posted January 16, 2018 So...I reverted to 10.3.2 and the audible latency is still there. I can record my guitar with no problem using Low Latency mode...that works...but, I like to hear the effects when I am playing and recording, if at all possible. Here is what I have done so far but to no avail: - SMC and PRAM reset - Reverted to Logic 10.3.2 from 10.3.3 - Verified audio interface (Duet USB) is not the problem through direct monitoring through Logic - Unclicked Core Audio => Apply Changes => Clicked Core Audio => Apply Changes [this worked once but the latency came back later] - No plugins instantiated - Ran exact same setup in Digital Performer 9.5 and had no problems whatsoever with audible latency Why would there be no audible latency in DP but audible latency in Logic using the exact same setup on the same computer??? Thanks. Quote Link to comment Share on other sites More sharing options...
JakobP Posted January 16, 2018 Share Posted January 16, 2018 ... I can record my guitar with no problem using Low Latency mode...that works... Strange, that seems to indicate that there are latency inducing plugins in your signal path... In your project, when you enabled LLM, open the mixer in "All" mode and look for plugins that have turned orange, can't you see any ? Quote Link to comment Share on other sites More sharing options...
deckard1 Posted January 16, 2018 Author Share Posted January 16, 2018 ... I can record my guitar with no problem using Low Latency mode...that works... Strange, that seems to indicate that there are latency inducing plugins in your signal path... In your project, when you enabled LLM, open the mixer in "All" mode and look for plugins that have turned orange, can't you see any ? Hey JakobP, That is absolutely correct. Thanks. I didn't realize, until David pointed it to me, that a bypassed plugin can still affect latency. So, the bypassed plugins were producing the latency, unbeknownst to me. I somehow thought if the plugins were bypassed they would have no effect regarding latency. Apparently, bypassed plugins still have an 'effect' for automation purposes. Quote Link to comment Share on other sites More sharing options...
JakobP Posted January 16, 2018 Share Posted January 16, 2018 You're welcome ...Apparently, bypassed plugins still have an 'effect' for automation purposes. That's my guess too. Quote Link to comment Share on other sites More sharing options...
deckard1 Posted January 20, 2018 Author Share Posted January 20, 2018 Just wanted to confirm that I tried it out yesterday and that was indeed the problem...bypassed plugins causing the audible latency. Quote Link to comment Share on other sites More sharing options...
Arnaud Posted January 20, 2018 Share Posted January 20, 2018 Apparently, bypassed plugins still have an 'effect' for automation purposes. Exactly, if bypassed effects caused no latency (or any different latency from when they are on, for that matter), turning them back on, or vice-versa (by any automated or non-automated means) would each time cause a nasty audible click, because Logic would have to instantly change the latency of the signal path. Quote Link to comment Share on other sites More sharing options...
deckard1 Posted January 20, 2018 Author Share Posted January 20, 2018 Apparently, bypassed plugins still have an 'effect' for automation purposes. Exactly, if bypassed effects caused no latency (or any different latency from when they are on, for that matter), turning them back on, or vice-versa (by any automated or non-automated means) would each time cause a nasty audible click, because Logic would have to instantly change the latency of the signal path. How come certain plugins cause latency and others do not? Seems to be a couple of Waves plugins I own that have the latency in this case. Quote Link to comment Share on other sites More sharing options...
triplets Posted January 21, 2018 Share Posted January 21, 2018 How come certain plugins cause latency and others do not? Seems to be a couple of Waves plugins I own that have the latency in this case. Plugins with a lookahead function like multipressors and limiters will create latency. Plugins that do heavy computations for analogue simulations will create latency. Most of the classic Waves stuff mimics analogue circuitry, so there's latency. Quote Link to comment Share on other sites More sharing options...
deckard1 Posted January 23, 2018 Author Share Posted January 23, 2018 How come certain plugins cause latency and others do not? Seems to be a couple of Waves plugins I own that have the latency in this case. Plugins with a lookahead function like multipressors and limiters will create latency. Plugins that do heavy computations for analogue simulations will create latency. Most of the classic Waves stuff mimics analogue circuitry, so there's latency. Thanks. That makes perfect sense. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.