YovahInc Posted September 15, 2021 Share Posted September 15, 2021 Hi, all, I can't lengthen an audio region by dragging the start point back. I've attached a GIF to show how weird this is. I can shorten the beginnig of the region just fine, but once I do that, I can't drag the region start past the new point I've just shortened it to. If I try 1,000 times in a row, eventually one of those times will work. You can see in the GIF I'm successful about after 20 tries. Any help is appreciated. Quote Link to comment Share on other sites More sharing options...
triplets Posted September 16, 2021 Share Posted September 16, 2021 What happens if you move the region further to the right, can you extend the whole region then? Quote Link to comment Share on other sites More sharing options...
YovahInc Posted September 17, 2021 Author Share Posted September 17, 2021 What happens if you move the region further to the right, can you extend the whole region then? As seen in the GIF, this doesn't fix the issue Yes, it's a very long region, but other, short regions in the same project were behaving this way too Quote Link to comment Share on other sites More sharing options...
fisherking Posted September 17, 2021 Share Posted September 17, 2021 does it happen in other projects? have you rebooted your mac..? Quote Link to comment Share on other sites More sharing options...
triplets Posted September 17, 2021 Share Posted September 17, 2021 Yes, it's a very long region, but other, short regions in the same project were behaving this way too Were the other regions also on the negative side of the timeline? Quote Link to comment Share on other sites More sharing options...
YovahInc Posted September 17, 2021 Author Share Posted September 17, 2021 Yes, it's a very long region, but other, short regions in the same project were behaving this way too Were the other regions also on the negative side of the timeline? Nope, they were a clean bounce in place of a few seconds of this region Quote Link to comment Share on other sites More sharing options...
triplets Posted September 17, 2021 Share Posted September 17, 2021 Does this happen on this project only, or on all your projects? Quote Link to comment Share on other sites More sharing options...
YovahInc Posted September 17, 2021 Author Share Posted September 17, 2021 Never before, been using Logic for years. This was the first time I've ever seen this, it's very weird. Quote Link to comment Share on other sites More sharing options...
fisherking Posted September 17, 2021 Share Posted September 17, 2021 does it happen in other projects? have you rebooted your mac..? Quote Link to comment Share on other sites More sharing options...
triplets Posted September 17, 2021 Share Posted September 17, 2021 Never before, been using Logic for years. This was the first time I've ever seen this, it's very weird. Does it happen on THIS project, or does it happen with ALL the projects? Quote Link to comment Share on other sites More sharing options...
YovahInc Posted September 17, 2021 Author Share Posted September 17, 2021 Does it happen..? Only in this project, as far as I see Quote Link to comment Share on other sites More sharing options...
triplets Posted September 17, 2021 Share Posted September 17, 2021 Only in this project, as far as I see That's good then. You might have project corruption. Create a new one, import what you need, and see if the behavior went away. Quote Link to comment Share on other sites More sharing options...
fisherking Posted September 17, 2021 Share Posted September 17, 2021 thanks, both of you, for ignoring my post... Quote Link to comment Share on other sites More sharing options...
triplets Posted September 17, 2021 Share Posted September 17, 2021 thanks, both of you, for ignoring my post... Relax, I've been ignored many times. Quote Link to comment Share on other sites More sharing options...
fisherking Posted September 17, 2021 Share Posted September 17, 2021 thanks, both of you, for ignoring my post... Relax, I've been ignored many times. apologies; suffered a personal loss late last night, and not handling things well this morning. love this place, will endeavor to 'lighten up'... Quote Link to comment Share on other sites More sharing options...
triplets Posted September 17, 2021 Share Posted September 17, 2021 Is all good, sorry about your loss. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.