Leggett Posted June 30, 2021 Share Posted June 30, 2021 Prior versions of Logic chased the sustain pedal (cc64) just fine. Since 10.6.2 not at all. Have to roll over event to trigger. Occurs in all instruments, Logic/Kontakt/VEP. Chase settings in preferences are set correctly. Anyone else having this or is it me? Thanks for any advice. Quote Link to comment Share on other sites More sharing options...
Atlas007 Posted July 1, 2021 Share Posted July 1, 2021 Didn't notice it yet... I'll have to test it... Not at the studio presently... Quote Link to comment Share on other sites More sharing options...
Leggett Posted July 2, 2021 Author Share Posted July 2, 2021 Thanks! Quote Link to comment Share on other sites More sharing options...
Atlas007 Posted July 2, 2021 Share Posted July 2, 2021 Ok, just tested same summarily. Works fine over here. Quote Link to comment Share on other sites More sharing options...
Leggett Posted July 2, 2021 Author Share Posted July 2, 2021 Good to know. Thanks Atlas! ....The plot thickens Quote Link to comment Share on other sites More sharing options...
Atlas007 Posted July 2, 2021 Share Posted July 2, 2021 Ho well, Logic is packed with those idiosyncris... Just now, after unpacking a take folder captured recording from a summing stack to existing track, Logic created a new track, giving it the name of the master track and put the resulting region onto it (leaving the original master track empty. Resulting audio playback was coming from the empty master track, the newly created track (understandably) and also from the two subtracks (from the original master track while still empty - no region onto it). Additionally, it was impossible to move back the region from the newly created track to the original master track stack. In order to succeed, I had to close the stack, move the region to an empty audio track, then from that audio track to the original master track stack. Go figure! Quote Link to comment Share on other sites More sharing options...
Leggett Posted July 2, 2021 Author Share Posted July 2, 2021 Thick plot indeed! Quote Link to comment Share on other sites More sharing options...
Leggett Posted July 2, 2021 Author Share Posted July 2, 2021 I've never figured out how to move a region back to a take folder. Other than undo's Quote Link to comment Share on other sites More sharing options...
JakobP Posted July 2, 2021 Share Posted July 2, 2021 I've seen midi chase show buggy behavior here: https://www.logicprohelp.com/viewtopic.php?f=1&t=147472&hilit=chase https://www.logicprohelp.com/viewtopic.php?f=1&t=147472&p=821613&hilit=chase#p821613 I've never figured out how to move a region back to a take folder. Other than undo's I would avoid using the undo command under these circumstances, this bug is nasty, sounds like Atlas007 also could have been bitten by it ? ...after unpacking a take folder captured recording from a summing stack to existing track, Logic created a new track, giving it the name of the master track... https://www.logicprohelp.com/viewtopic.php?f=42&t=156676 Quote Link to comment Share on other sites More sharing options...
Atlas007 Posted July 2, 2021 Share Posted July 2, 2021 ...I've never figured out how to move a region back to a take folder. Other than undo's I would avoid using the undo command under these circumstances, this bug is nasty, sounds like Atlas007 also could have been bitten by it ? ...after unpacking a take folder captured recording from a summing stack to existing track, Logic created a new track, giving it the name of the master track... https://www.logicprohelp.com/viewtopic.php?f=42&t=156676 Indeed... Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.